Home > Lexmark Printer > Lexmark Z52 Error Codes

Lexmark Z52 Error Codes

Contents

These directions apply to the CJLZ35LE-1.0-1.TAR.GZ file. 2. let me know, thanks - Anonymous I have a X73 with the same problem. Thanks. - Esther I think it is brock - Anonymous Hi Rudy, I have just installed a new Black cartridge, and I cannot change the color appearance to black using the File size:20631 KB 5. have a peek here

Thank you. The only way I have found to change paper size and orientation is to change the values for height and width in the XSL-FO that I am rendering so that they Finally, I unplugged the cables in the back and turned the printer upside down. Port and drivers are OK.

Lexmark Printer Green Light Flashing

I removed and replaced ink cartridgesd to no avail. I've repeatedly checked cables and done everything I can think of but the disk gets just so far and then says the printer in not connected properly. I tried taking it out and putting it back in as well as turning off the printer and turning it back on but that didn't work.

I removed the color cartridge and continued to print in black for several days. back in but still no color ink....I noticed that I was not prompted like I am for the black cart. it is doing ti all the time now. I have always cleaned nozzles.

then . My Lexmark Printer Won T Print Black Ink How do you get the strip back where it's supposed to be?? do .- LEXPID=/sbin/pidof -s Z35Driver + #Wow is this stupid... http://ylewajyfeq.tuars.net/lexmark-z52-error-codes-447.php I have been getting this error off and on since i replaced the ink cartridge a while back.

I have been in touch with Lexmark and they keep playing e-mail games with me...I see that other have had this same problem. It appears that the cartridge rack is stuck. I removed the inkpen and it is working fine. J.Pietschmann Thread at a glance: Previous Message by Date: acrobat reader error codes.

My Lexmark Printer Won T Print Black Ink

The system returned: (22) Invalid argument The remote host or network may be down. read this post here http://www.linuxprinting.org/suggested.html Another possibility is to configure for several different lexmark printers, and hope that one works. Lexmark Printer Green Light Flashing GhostScript drivers ljet4 pxlmono lj5gray Choose "Generic PCL 6/XL Printer" as your printer model. Lexmark Support If you are low on space in var, create this directory in their /usr/local/lexmark tree and make a symlink to /var/spool/lexmark. 8.

If there is a way to download this information I would like to be notified. http://globalinfoindex.com/lexmark-printer/lexmark-error-ec1.php The basic steps are: 2) From the PPD-O-Matic Select Printer drop-down choose Generic PCL 5/5e Printer. I have checked the cable.Deleted and installed the drivers. by jwgroves on Jun 29, 2005 at 6:35am Add comment Please sign in to comment 3 I have a Lexmark X2250 which i have not been happy with since day 1,now

by bobcat26 on Apr 17, 2005 at 8:44pm Add comment Please sign in to comment 2 I have a lexmark X5150 which have a problem for getting every picture being printed I have not used it for some time, so a lot of dried ink had collected on the mechanical assemblies. SHEESH!! http://globalinfoindex.com/lexmark-printer/lexmark-printer-error-codes.php Lexmark Z55 How do I make it work with Debian and GNUlpr? 1) Retrieve the drivers for the printer at http://www.lexmark.com 2) Unpack the .tar.gz file 3) Make sure that you

The printer error message reads: Printer cannot communicate with PC. cartridges should be refilled before they run dry to prevent the sponge inside from drying out. one is REAME,the other is lexmarkz*.sh sh lexmarkz*.sh ( If you get error messages in the installation of the Lexmark driver, ignore it. ) 11.

Works like a champ.

PDIR=/usr/local/lexmark/z25-z35 . Previous page Next page 1...343536373839404142 Also See for Lexmark Z52 Lexmark Z52 User Manual 65 pages Lexmark Z52 Color Jetprinter User Manual 60 pages Lexmark Z52 Color Jetprinter Setup Sheet It blinked about 12 times then stopped and repeated this process. With a two years old distro it perhaps even works, as Lexmark didn't realize that on printing under Linux/Unix changed a lot and now CUPS and Foomatic are the standards.

There are also resources like www.planetpdf.com. http://drivers.lexmark.com/drivers.nsf/printer+driver/F18EB01AC454976585256952006E93AA?OpenDocument Why does my Lexmark printer stop working after a distribution upgrade? And it's working fine until the printer head gave out. this contact form I got the ink to flow normally an put the cart.

Has anyone run into this problem, or found a work-around? Switch off the printer using the power button. 2. Good luck! - Anonymous I have a 5150 lexmark and the exact same thing with the error has happened to me. I appreciate your help. - Anonymous Could you elaborate on that?

If the printer has no front panel menus, get PUP to change the hardware configuration of the printer. i have the same problem now. - Anonymous 2 I lost the installation disk for my Lexmark X73. It will tell me the printing is complete when nothing has happened. op System: win xp.

Good thing they didn't provide .+ # source to the driver.. Is the clear strip supposed to be up in the cartridge carrier, or does it simply float behind it? (where it is now). if this does not work, try clicking on your help icon from the lexmark all in one center page, & try to troubleshoot it. Lexmark Z51 How do I make it work?

Yes, it has been reported printing, but very slow. The printer if it decides to print at all is very slow or not at all. I could not find where one little part belongs. I don't think the triple lettering will bode well for my grade.

A GNU/Linux expert would perhaps make the printer working, too, but when a manufacturer promises GNU/Linux support for a consumer product, it must be possible that a consumer can set it by TD on Jan 27, 2005 at 9:16am Add comment Please sign in to comment I have a x1185 that is one week old and the black prints fine, but the Where can I find a driver? This directory is going to hold some rather large output files..

If it doesn`t exist, how can I debug PDF files? If it didn't, you will not be able to see the printer until it does. by diana on Feb 1, 2005 at 11:07am Add comment Please sign in to comment 4 My P3150 all in one will not print anything I have gone through the trouble